16 Jul

Yes, You Want One – An ‘Anti-Drain-Back-Valve’ in Your Oil Filter

[This treatise was taken from a number of sites on the internet (and then edited some) and seems to be good guidance relative to the need for the anti-drain-back-valve in your Morgan’s oil filter.  The question has come up a few times and we have tried to answer it, but haven’t really been convincing.  This seems to do it.  FYI, Race Cars with oil preheaters, etc., may have different requirements.  Mark]

Your Engine ‘oil filter’ is a very important component; it traps dirt and debris, preventing them from circulating throughout the engine.  This protects vital internal parts such as bearings, journals, and cylinder walls.

Another way the oil filter protects and helps lubricate the engine is using an anti-drain back-valve.  This valve is predominantly used within the spin-on versions of today’s oil filter and not a part of the older style of cartridge style filters (such as the original style 1950s – 1960s Plus 4s filters).  Although you may not have heard of it before or know what it does, this valve is extremely important.  Extensive engine damage can result if it isn’t working properly.

Oil filter design

The oil filter’s design might seem simple, but there is a lot more to an oil filter than you might think. Before delving into the details of what damage can be caused by a faulty anti-drain back valve, it’s a good idea to know how a car oil filter works. Typical oil filter components include the following:

  • Tapping or cover plate: This is the plate at the bottom of the filter.  It serves as an entry and exit point for oil. It also contains a threaded center hole, which allows the filter to attach to the engine.
  • Filter medium: Dirt and debris are trapped in the filter medium.  Typically, it is constructed from microscopic cellulose fibers along with synthetic fiber.  It is then saturated with resin for added strength.  The filter medium is folded into pleats to create a greater surface area.
  • Center steel tube: The center steel tube provides a structure for the filter.  It also allows filtered oil to return to the engine.
  • Relief valve: The relief valve opens when oil pressure is too great due to clogged filter media.  This allows unfiltered oil to exit through the center tube to prevent engine starvation.
  • End disc: Some oil filters use an end disc to prevent unfiltered oil from leaking into the center tube.  Others use a sealant instead.
  • Retainer: As the name implies, the retainer keeps the filter medium and end disc tight against the tapping plate.
  • Anti-drain back valve: The anti-drain-back-valve prevents oil from draining out of the filter when the engine is turned off.

Engine damage caused by a faulty anti-drain-back-valve

During an oil change, it’s recommended you put fresh oil in the new filter before installing it.  This is so oil is available to the engine as soon as it’s started.

The anti-drain-back-valve serves a purpose that’s like this oil change strategy.  Every time your engine is shut off, the valve keeps oil from draining out of the filter.  This allows the engine to receive oil immediately upon start up.

A faulty anti-drain-back-valve lets oil drain back into the engine.  This keeps oil from getting to the engine when it’s first started.  The result is engine wear and eventual failure from lack of lubrication.  Low-quality oil filters often have a poorly designed anti-drain-back-valve that doesn’t work properly.

Don’t settle for low-quality oil filters

The best way to avoid anti-drain back problems is to use a high-quality filter.  A good filter usually has a robust anti-drain-back-valve, designed to protect your Morgan’s engine.

15 Jul

Sad News – Paul Alfred Davidson 8/25/1951 – 7/12/2018

Celebration of LIfe for Paul A. Davidson, Hosted by Alexandra Petrenko

Paul Alfred Davidson 8/25/1951 – 7/12/2018

Parking:  Pumphrey’s has staff to assist with parking. They have a parking lot on site that can accommodate about 30 cars. If their lot is full, there is a parking lot just behind the building to the north and a parking garage 1/2 block to the north. Access to both the lot and garage are off Middleton Lane.  Pumphrey’s is less than a 5 minute walk from Bethesda Metro.

Please forward the invitation to those who knew and loved him.

It is so very unfortunate but also inevitable that members of the Morgan community move on.  Paul Davidson of MD, was a mainstay in the MCCDC Club for many years.  I knew him well, visited his house many times, and served as VP of the Club when he was President of the Club in 1990 or so.  I am sure there are others in MOGSouth that called him a friend, as well.

His blue 1953 Flat Rad Plus 4 was the darling at every meet.  I hope it finds a home with another enthusiast like Paul.

In addition to Morgans, Paul loved music and supported WPFW 89.3 FM, which had several programs he particularly enjoyed. Please consider donating to WPFW 89.3 FM on behalf of Paul.  http://www.wpfwfm.org/radio/

For those that knew Paul, remember the good times and raise a glass in his honor.

Cheers, Mark

 

 

13 Jul

Updates – 2018 MOGSouth Holiday Party – Now on St Simons Island GA – 1 Dec 2018

The 2018 MOGSouth Holiday Party details have finally come together.

The 2018 Holiday Party will be held at the St Simons Island King and Prince Beach and Golf Resort, on Saturday 1 Dec 2018. 

[Note:  We were trying to have the Holiday Party on Jekyll Island but there seems to be no availability.  A large insurance corporation is having their annual conference there and has the entire island booked.   As it turns out,  St Simons is actually better!  More to see and do!   Mark]

Although the Holiday Banquet is on Saturday evening, 1 December,  for even more fun, it is recommended you arrive on Friday 30 November.  There is a trolley tour scheduled for Saturday morning that gives you great views and lots of historic insight into St Simons Island.  This is not something you will want to miss.  The Trolley Tour is $20 per person.   FYI, this Trolley Bus has received numerous accolades, year after year.  We will collect the money as we get on the Trolley Bus.  Please bring cash or personal check to pay.  We cannot take credit cards.

Be advised, the trolley may not be able to handle our entire group in one trip, so if interested, you have to send an email to Mark Braunstein so he can put you on the trolley list.  First come, first served.   If you want to go with friends, make sure you let us know.

We have commited to fill at least one trolley bus which is scheduled to go out at 10:00 AM (hotel’s front door) and should we fill a second trolley bus, the second group will go out at 12:00 PM.  Who knows, things could change but this is the plan.  We will let you know if something changes.

The trolley isn’t the only thing to do on St Simons Island.   Among other things, there are museums, a lighthouse and the lovely Hofwyl-Broadfield Plantation.  Go to the St Simons Island Website to see all there is to do.

The weather in St Simons Island, during our visit, should be superb.  The temperature is moderate (High/Low °F) – 70°/ 53° and, on average, it’s the period of the lowest rain fall all year.  Anything can happen, but it’s well worth the risk.  Bring your Morgan!

Holiday Party Hotel Details: The full name of the hotel is The King and Prince Beach and Golf Resort. It ls located at 201 Arnold Rd., St Simons Island, GA 31522, 800-342-0212, www.kingand prince.com

Call to make reservations.   We have negotiated a group rate at the hotel so be sure to mention Morgan Car Club and/or MOGSOUTH when making your reservations.   You will have to call and reserve and pay for your rooms individually.   These room rates are as follows.

Standard Rooms at $139, Partial Ocean View at $154 and Ocean Front Rooms at $169, plus taxes and fees.   It is recommended that you use whatever discounts, AARP, Military, etc., you have.    The view of the ocean is superb!!

If you are coming to St Simons for the Holiday Party please send an email to Mark Braunstein so he can keep a total for the hotel.  The Hotel needs to know how many folks are coming so that they can order sufficient food.  That, and MOGSouth will have to pay for meals that aren’t eaten so please let Mark Braunstein know if you are coming or must cancel. 

The Holiday Banquet will be a buffet dinner, and will include a choice of Chef’s Garden Salad, a Holiday Waldorf Salad, Roasted Turkey, or Sunset Farms Queen of Dixie Smoked Ham.  The banquet is $41 per person plus tax.  Again, we will collect money at the door to the Banquet.  Please bring cash or personal check to pay.  We cannot take credit cards.

  • Side dishes include Buttery Whipped Potatoes, Candied Sweet Potatoes, Roasted Brussel Spouts in Pecan butter, and Green Bean Casserole.
  • Dinner Roles and Desserts (Pecan Pie, Pumpkin Pie, and Red Velvet Cake) will be offered as well.  Of course there will be Coffee and Tea available.
  • A Cash Bar will also be available prior to and during the Holiday Banquet.

In keeping with tradition there will be a MOGSouth Hospitality Room open at appropriate times during the weekend.  Tentatively it will be in the Wesley Cottage, but do check with the Hotel’s front desk when you check in to verify.

[Be advised that MOGSouth is subsidizing this event.  (In case you wondered where your dues went!) There may be cheaper budget hotels down the street that look appealing, however, if we don’t reach our targeted attendance at this hotel, we will have additional fees to pay and everyone else’s costs will go up.  Please don’t do it!   Mark]

Looking forward to seeing everyone!!!   Chuck and Karen Bernath

11 Jul

Updates – 2018 MOGSouth Fall Meet, Augusta GA, 14-16 Sep.

The MOGSouth Fall Meet will be in Augusta, GA Sep 14 – 16

The Meet Host Hotel is The Partridge Inn, 2110 Walton Way, Augusta GA 30904  (Tel. 706-737-8888)

The Partridge Inn is an historic southern style and quaint hotel, but now in the hands of Hilton and is efficient, clean and well-managed.  It has a roof-top bar that overlooks the city and balcony rooms that overlook the beautiful pool and lounging area.

We have negotiated superb Group rates for the rooms. This rate includes breakfast for either a single person or a couple in the room.

Standard Rooms are $139.00 per night, Suites are $149.00 and rooms with Balconies at $159.00.

Guests need to call the Partridge Inn directly (706-737-8888) for their reservations using the MOGSouth group name

These rooms will be held for MOGSouth until August 15 . . . so please make your reservations now to be guaranteed these great rates!

The Partridge Inn has also reserved secured, covered parking at no extra charge for our Morgans.

The Hospitality Room will be in the Partrirdge Inn’s  ‘Cigar Bar’ (not to worry it will be non smoking!) on the first floor.  It will be open to MOGSouth only, on both Friday and Saturday, 14/15 Sep from 2:30 PM until 10 PM.

In addition to the Partridge Inn’s own restaurant, there are a number of restaurants nearby.

  • Raes Coastal Café, 3208W. Wimbledon Dr. Augusta GA 30909 – 706-738-1313 (4 Miles)
  • Finch and Fifth, 379 Highland Ave., Augusta GA – 706-364-5300 (2 Miles)
  • Ephesus Restaurant, Mediterranean / Turkish, 3102 Washington Rd., Augusta GA  – 762-994-0180 (5 miles)
  • Whiskey Bar Kitchen, Japanese / Burgers, 1048 Broad St., Augusta GA 30901 – 706-814-6159 (3 miles)

We will have a group dinner at 6:30PM on Saturday evening at  Cucina 503, 502 Fury’s Ferry Road Suite 503, Augusta GA 30309 – 762-994-0142 (7.5 miles)

The Partridge Inn Shuttle is also available at no charge for those not wanting to drive out in the evening.  (You must go to the front desk and reserve a spot on the shuttle.)

If you are curious, go to the Hotel’s  website  The Partridge Inn and check out the photos of the Partridge Inn.

Come and luxuriate for a great weekend get together in Augusta!!!

Dorothy and Glenn Moore

10 Jul

Latest News – New Morgan Four Wheelers (https://justbritish.com/ – 4 July 2018)

A long-loved British sports car is finally returning to the US. Morgan Motor Company, in response to U.S. Morgan dealers unfulfilled demand for 4 wheeled Morgans and also the disappointing lack of progress in implementing the Replica Car Bill, is now addressing the issue proactively.

Last week Morgan Motor Company announced that they are prepared to manufacture a functional rolling chassis in both Roadster and Plus 4 variants, that can then be shipped to the US, using the specially constructed vehicle route to market.

It is fully appreciated that there has been a significant hiatus regarding supply of four-wheeled Morgan vehicles to the US. Additionally,  the proposed Replica Car Bill has stalled significantly during the last 2 years and is still without any clear steer on the outcome with regards to both timing and legislative requirements. We believe there is a huge pent-up demand for traditional Morgans in the U.S.

Morgan plans an initial build of 40 Roadsters and 40 Plus 4’s during the remainder of 2018.

Upon hearing the news in San Francisco, Bill Fink of Morgan Cars USA was too jubilant at the prospect of new cars to dwell about the low number of vehicles.

“We have long awaited the opportunity to provide our customers with classic Morgans again. After the days without new 4-wheeled cars started stretching into years, and all the time spent waiting for implementation of the Fast Act – this is a very happy turn of events.”

Immediately available models include the Morgan Plus 4 (base price MSRP $69,995) and the Roadster 3.7 (base price MSRP $79,995.)  Freight, options, taxes, and fees are additional.

With the suggestion that as few as 80 vehicles will be built to meet the demand, and factoring in the Morgan devotees on dealers’ wait lists, the available build dates will be filled quickly.

Contact the authorized dealers (MOGSouth Supporters are listed here) to voice your interest and get any questions answered.

 

04 Jul

On-board diagnostics (OBD) (Wikipedia and Morganatica)

On-board diagnostics (OBD) is an automotive term referring to a vehicle’s self-diagnostic and reporting capability. OBD systems give the vehicle owner or repair technician access to the status of the various vehicle subsystems. The amount of diagnostic information available via OBD has varied widely since its introduction in the early 1980s versions of on-board vehicle computers.  Early versions of OBD would simply illuminate a malfunction indicator light or “idiot light” if a problem was detected but would not provide any information as to the nature of the problem.

Modern OBD implementations use a standardized digital communications port to provide real-time data in addition to a standardized series of diagnostic trouble codes, or DTCs, which allow one to rapidly identify and remedy malfunctions within the vehicle.

[ODB implementations have been mandated in Europe since 2001 so it is believed that all Morgans since that date, e.g. late model Plus 8s, Roadsters and Aero 8, as well as the new ‘component’ Morgans expected in 2018 will have OBD capabilities.  Consumer level ODB readers are available just about everywhere and you can buy them to assist you in troubleshooting any faults.  Dedicated automotive repair facilities will most likely utilize more sophisticated ‘OEM-like’ ODB code readers.  Mark]

EOBD

The EOBD (European on board diagnostics) regulations are the European equivalent of OBD-II, and apply to all passenger cars first registered within EU member states since January 1, 2001.

The technical implementation of EOBD is essentially the same as OBD-II, with the same SAE J1962 diagnostic connector and signal protocols being used.

Each of the EOBD fault codes consists of five characters: a letter, followed by four numbers. The letter refers to the system being interrogated e.g. Pxxxx would refer to the powertrain system. The next character would be a 0 if complies to the EOBD standard. So it should look like P0xxx.

The next character would refer to the sub system.

  • P00xx – Fuel and air metering and auxiliary emission controls.
  • P01xx – Fuel and air metering.
  • P02xx – Fuel and air metering (injector circuit).
  • P03xx – Ignition system or misfire.
  • P04xx – Auxiliary emissions controls.
  • P05xx – Vehicle speed controls and idle control system.
  • P06xx – Computer output circuit.
  • P07xx – Transmission.
  • P08xx – Transmission.

List of OBD Fault Codes

P1000 OBD-II Monitor Testing Incomplete
P1001 KOER Test Cannot Be Completed
P1039 Vehicle Speed Signal Missing or Improper
P1051 Brake Switch Signal Missing or Improper
P1100 Mass Air Flow Sensor Intermittent
P1101 Mass Air Flow Sensor out of Self-Test Range
P1112 Intake Air Temperature Sensor Intermittent
P1116 Engine Coolant Temperature Sensor is out of Self-Test Range
P1117 Engine Coolant Temperature Sensor Intermittent
P1120 Throttle Position Sensor out of range
P1121 Throttle Position Sensor Inconsistent with Mass Air Flow Sensor
P1124 Throttle Position Sensor out of Self-Test Range
P1125 Throttle Position Sensor Intermittent
P1127 Heated Oxygen Sensor Heater not on During KOER Test
P1128 Heated Oxygen Sensor Signals reversed
P1129 Heated Oxygen Sensor Signals reversed
P1130 Lack of Upstream Heated Oxygen Sensor Switch – Adaptive Fuel Limit – Bank No. 1
P1131 Lack of Upstream Heated Oxygen Sensor Switch – Sensor Indicates Lean – Bank No. 1
P1132 Lack of Upstream Heated Oxygen Sensor Switch – Sensor Indicates Rich – Bank No. 1
P1135 Ignition Switch Signal Missing or Improper
P1137 Lack of Downstream Heated Oxygen Sensor Switch – Sensor Indicates Lean – Bank No. 1
P1138 Lack of Downstream Heated Oxygen Sensor Switch – Sensor Indicates Rich – Bank No. 1
P1150 Lack of Upstream Heated Oxygen Sensor Switch – Adaptive Fuel Limit – Bank No. 2
P1151 Lack of Upstream Heated Oxygen Sensor Switch – Sensor Indicates Lean – Bank No. 2
P1152 Lack of Upstream Heated Oxygen Sensor Switch – Sensor Indicates Rich – Bank No. 2
P1157 Lack of Downstream Heated Oxygen Sensor Switch – Sensor Indicates Lean – Bank No. 2
P1158 Lack of Downstream Heated Oxygen Sensor Switch – Sensor Indicates Rich – Bank No. 2
P1220 Series Throttle Control fault
P1224 Throttle Position Sensor B out of Self-Test Range
P1230 Open Power to Fuel Pump circuit
P1231 High Speed Fuel Pump Relay activated
P1232 Low Speed Fuel Pump Primary circuit failure
P1233 Fuel Pump Driver Module off-line
P1234 Fuel Pump Driver Module off-line
P1235 Fuel Pump Control out of range
P1236 Fuel Pump Control out of range
P1237 Fuel Pump Secondary circuit fault
P1238 Fuel Pump Secondary circuit fault
P1250 Lack of Power to FPRC Solenoid
P1260 Theft Detected – Engine Disabled
P1270 Engine RPM or Vehicle Speed Limiter Reached
P1288 Cylinder Head Temperature Sensor out of Self-Test Range
P1289 Cylinder Head Temperature Sensor Signal Greater Than Self-Test Range
P1290 Cylinder Head Temperature Sensor Signal Less Than Self-Test Range
P1299 Cylinder Head Temperature Sensor Detected Engine Overheating Condition
P1309 Misfire Detection Monitor not enabled
P1351 Ignition Diagnostic Monitor circuit Input fault
P1352 Ignition Coil A – Primary circuit fault
P1353 Ignition Coil B – Primary circuit fault
P1354 Ignition Coil C – Primary circuit fault
P1355 Ignition Coil D – Primary circuit fault
P1356 Loss of Ignition Diagnostic Module Input to PCM
P1358 Ignition Diagnostic Monitor Signal out of Self-Test Range
P1359 Spark Output circuit fault
P1364 Ignition Coil Primary circuit fault
P1380 VCT Solenoid Valve circuit Short or Open
P1381 Cam Timing Advance is excessive
P1383 Cam Timing Advance is excessive
P1390 Octane Adjust out of Self-Test Range
P1400 Differential Pressure Feedback Electronic Sensor circuit Low Voltage
P1401 Differential Pressure Feedback Electronic Sensor circuit High Voltage
P1403 Differential Pressure Feedback Electronic Sensor Hoses Reversed
P1405 Differential Pressure Feedback Electronic Sensor circuit Upstream Hose
P1406 Differential Pressure Feedback Electronic Sensor circuit Downstream Hose
P1407 EGR No Flow Detected
P1408 EGR Flow out of Self-Test Range
P1409? EGR Vacuum Regulator circuit malfunction
P1409? Electronic Vacuum Regulator Control circuit fault
P1410 EGR Barometric Pressure Sensor VREF Voltage
P1411 Secondary Air is not being diverted
P1413 Secondary Air Injection System Monitor circuit Low Voltage
P1414 Secondary Air Injection System Monitor circuit High Voltage
P1442 Secondary Air Injection System Monitor circuit High Voltage
P1443 Evaporative Emission Control System – Vacuum System – Purge Control Solenoid or Purge Control Valve fault
P1444 Purge Flow Sensor circuit Input Low
P1445 Purge Flow Sensor circuit Input High
P1450 Inability of Evaporative Emission Control System to Bleed Fuel Tank
P1451 EVAP Control System Canister Vent Solenoid Circuit Malfunction
P1452 Inability of Evaporative Emission Control System to Bleed Fuel Tank
P1455 Substantial Leak or Blockage in Evaporative Emission Control System
P1460 Wide Open Throttle Air Conditioning Cutoff circuit malfunction
P1461 Air Conditioning Pressure Sensor circuit Low Input
P1462 Air Conditioning Pressure Sensor circuit high Input
P1463 Air Conditioning Pressure Sensor Insufficient Pressure change
P1464 ACCS to PCM High During Self-Test
P1469 Low Air Conditioning Cycling Period
P1473 Fan Secondary High with Fans Off
P1474 Low Fan Control Primary circuit
P1479 High Fan Control Primary circuit
P1480 Fan Secondary Low with Low Fans On
P1481 Fan Secondary Low with High Fans On
P1483 Power to Cooling Fan Exceeded Normal Draw
P1484 Variable Load Control Module Pin 1 Open
P1500 Vehicle Speed Sensor Intermittent
P1501 Programmable Speedometer & Odometer Module/Vehicle Speed Sensor Intermittent circuit-failure
P1502 Invalid or Missing Vehicle Speed Message or Brake Data
P1504 Intake Air Control circuit malfunction
P1505 Idle Air Control System at Adaptive Clip
P1506 Idle Air Control Over Speed Error
P1507 Idle Air Control Under Speed Error
P1512 Intake Manifold Runner Control Stuck Closed
P1513 Intake Manifold Runner Control Stuck Closed
P1516 Intake Manifold Runner Control Input Error
P1517 Intake Manifold Runner Control Input Error
P1518 Intake Manifold Runner Control fault – Stuck Open
P1519? Intake Manifold Runner Control Stuck Open
P1520? Intake Manifold Runner Control circuit fault
P1519? Intake Manifold Runner Control fault – Stuck Closed
P1520? Intake Manifold Runner Control fault
P1530 Open or Short to A/C Compressor Clutch circuit
P1537 Intake Manifold Runner Control Stuck Open
P1538 Intake Manifold Runner Control Stuck Open
P1539 Power to A/C Compressor Clutch circuit Exceeded Normal Current Draw
P1549 Intake Manifold Temperature Valve Vacuum Actuator Connection
P1550 Power Steering Pressure Sensor out of Self-Test Range
P1605 PCM Keep Alive Memory Test Error
P1625 Voltage to Vehicle Load Control Module Fan circuit not detected
P1626 Voltage to Vehicle Load Control Module circuit not detected
P1650 Power Steering Pressure Switch out of Self-Test Range
P1651 Power Steering Pressure Switch Input fault
P1700 Transmission system problems
P1701 Reverse Engagement Error
P1702 Transmission system problems
P1703 Brake On/Off Switch out of Self-Test Range
P1704 Transmission system problems
P1705 Manual Lever Position Sensor out of Self-Test Range
P1709 Park or Neutral Position Switch out of Self-Test Range
P1710 Transmission system problems
P1711 Transmission Fluid Temperature Sensor out of Self-Test Range
P1713
thru
P172 Transmission system problems
P1729 4×4 Low Switch Error
P1740 Transmission system problems
P1741 Torque Converter Clutch Control Error
P1742 Torque Converter Clutch Solenoid Faulty
P1743 Torque Converter Clutch Solenoid Faulty
P1744 Torque Converter Clutch System Stuck in Off Position
P1745 Transmission system problems
P1746 Electronic Pressure Control Solenoid – Open circuit
P1747 Electronic Pressure Control Solenoid – Short circuit
P1749 Electronic Pressure Control Solenoid Failed Low
P1751 Shift Solenoid No. 1 Performance
P1754 Coast Clutch Solenoid circuit malfunction
P1756 Shift Solenoid No. 2 Performance
P1760 Transmission system problems
P1761 Shift Solenoid No. 3 Performance
P1762 Transmission system problems
P1767 Transmission system problems
P1780 Transmission Control Switch circuit is out of Self-Test Range
P1781 4×4 Low Switch is out of Self-Test Range
P1783 Transmission Over-Temperature Condition
P1784 Transmission system problems
P1785 Transmission system problems
P1786 Transmission system problems
P1787 Transmission system problems
P1788 Transmission system problems
P1789 Transmission system problems
P1900 Transmission system problems

[I haven’t personally verified that each of these codes exist or are as specified, so if you do find inconsistencies, please let me know.   Mark]

03 Jul

1968 Morgan Plus 8 A racer or a concours queen? The new owner gets to decide (Sports Car Market -July 2018)

Plus 8 Chassis number: R7022

Searching for new engines in the 1960s, Morgan concluded a deal with Rover for supply of its all-aluminum 3.5-liter V8, thus creating a car — the Plus 8 — that combined vintage charm with Cobra-like grunt.

Morgan’s Plus 4 chassis, strengthened and extended, formed the basis of the new car, while the existing Moss 4-speed gearbox was retained.  After a successful debut at the 1968 London Motor Show, production commenced at about 15 cars per month and continues to this day, although they now have BMW power.

While the traditionally styled Morgan’s brick-like aerodynamics restricted top speed to around 125 mph (more than fast enough for most people driving an open car), the Rover V8’s 168 bhp and 210 ft-lb of torque made for supercar performance through the gears. Indeed, in its later 3.9-liter form, the Plus 8 proved quicker by 80 mph than the contemporary Porsche 911 Turbo.

This all-matching-numbers early Morgan Plus 8 is the 22nd example of this landmark V8-engined model to leave the factory.

It was supplied new in February 1969 to the Half Moon Garage in Yorkshire.  [The picture shows a RHD car.  Reduced Value in the US?   Many would say so, but I personally like them.  In my mind, it adds credibility to a British Sports car.  Mark] 

Benefiting from a six-year, six-figure, ground-up restoration undertaken in the USA from renowned marque specialist and concours-winner the late Robert Couch, the car must be one of the best of its kind currently available.

Robert Couch is famous as restorer of the historic Morgan TT Replica CAB 652, previously campaigned by Peter Morgan, which in 1980 was overall winner of the prestigious Chinetti Concours at Lime Rock.

Carried on a new chassis, the aluminum body benefits from an all-new timber framework. Restored for Morgan’s 75th anniversary, although it did not make it to the U.K. for the celebrations, this Plus 8 comes with concours awards testifying to the quality of the restoration.

Acquired from the estate of the late Stephen S. Lester, SCV 901G has been stored in a climate-controlled facility as part of an extensive private collection of vehicles where it has been looked upon as a work of art.

The Morgan recently got an update that was done over two years. The work included a brand-new race engine installed by JE Developments, a recognized specialist in the preparation of Rover V8 engines.  This engine breathes via SU carburetors to accommodate FIA regulations.

The other race engine built by Robert Couch had on tap a massive 288 bhp and 275 ft-lb of torque (documented) and is included in the sale.

Despite its greatly enhanced performance, this car is said to cope equally easily with town driving or touring, and must be one of the quickest road-going first generation Plus 8s around.

For a year of its time away, the Morgan was at Richard Thorne’s workshop being fitted with every new FIA update required for historic racing, hillclimbing, and rallying anywhere in the world (Period G1 1966–69, valid to December 31, 2026).

All the work was bespoke in order to avoid drilling the body or dashboard to accommodate cut-off switches. The new FIA roll bars (front and rear) were custom made to ensure a perfect fit, while the side-impact bars were taken down below the door line to make getting in and out as easy as normal.

All this was done at great expense in order to preserve Robert Couch’s original workmanship. Even the spare-wheel cover has no external screws securing it to the rear frame; it simply slides in from underneath, making it easy to remove in order to refit the rear bumper and spare wheel for rally events. The car comes complete with full weather equipment, spare wheel, boot rack and tonneau cover (made to fit the new roll bars).

This well-documented car comes with its original restoration bills and is described as perfect for all uses.

SCM Analysis

This car, Lot 64, sold for £61,980 ($86,390), including buyer’s premium, at Bonhams’ Goodwood Members’ Meeting sale near Chichester, U.K., on March 18, 2018.

This is a slightly strange one. It’s a concours-restored car got up as a racer, but it doesn’t appear to have raced.  [A stock car prepared as a competition car but without any competition provenance is, in my opinion, simply a ‘bitsa’.  I personally question the value (the seller did really well here!) and would prefer to buy a stock car.  Mark]

It was offered — but didn’t sell — at Bonhams’ pre-Christmas sale at Olympia, London, when the original Holley-carbed engine was displayed on a stand behind it, but it had better luck here.

Lots of events — but not all of them

The car’s condition is beyond reproach, with several neat (though unnecessary for a racer) touches.  It could easily be raced.  Competition car sales history tells us that it’s always cheaper to buy someone else’s hard graft rather than build your own, but you’d have to accept that it would rapidly acquire some patina as some of the shine got knocked off.  [People are attracted to ‘shiney’ things . . . Mark]

But here’s the thing: It’s got FIA papers, but it’s Period G1 (1966– 1969) while most prestige events run to Period F (pre-1966) or have an even earlier cut-off of pre-1963.

As our subject car was built in 1968, circuit racing opportunities will not include such events as the Goodwood Revival. Perhaps its most obvious home is in the Historic Sports Car Club’s Historic Road Sports series, for road-legal cars manufactured up to 1970, with only mild modifications allowed. This series offers extra points for those cars driven to the races.

This car can take part in tour/race competitions such as Tour Britannia and Tour Auto, and it would do well in events such as the Manx Classic — a three-legged hillclimb competition whose classic category has a 1968 cut-off date.

This car is eligible for historic rallies, too. One brave soul once ran a Morgan in a British Historic Rally Championship when it was a mix of tarmac and forest events. He found that he had to rebuild the car after every thrash — and a sliding-pillar, ash-framed Morgan on rough gravel really is only for masochists. Discouraging competition use, however, this car was in super, near concours condition. I noted unnaturally shiny paint — although slightly

A big price for a terrific car

A Moss-box Plus 8 (made up to mid-1972, when the Rover 4-speed was adopted) would usually sell for about £30k ($42k) [I guess this has to be UK prices.  In my opinion, I would think a LHD Moss Box Plus 8, in the US,  should be valued at $55-60K.  Mark], perhaps a little more in this concours condition.

John Eales of JE Developments is “the man” as far as the Rover/ Buick aluminum V8 is concerned, so the currently installed FIA-legal race motor, making about 250 bhp, is the best there is.

These engines cost less than you’d think at £12k ($17k). The competition fuel cell, bespoke roll cage, Sparco harnesses and plumbed-in extinguisher probably cost up to $10k to add, but you never get your money back on “lifed” items like this, so technically this car’s value is something under $60k.

At Olympia, you can see how the seller might have arrived at the $113k to $140k estimate by adding up everything spent, but it was unsold at a reported top bid of $93,642.

The estimate for the second attempt, at Goodwood, was revised down to $85k to $100k. It hammered slightly behind that, but at a price approaching twice that of a standard early (narrow-bodied, as they got wider in tub and wings after 1976) road car.

Interestingly, a similar car, chassis 7259, also rebuilt on a new chassis and ash frame and race prepared to the same specs with a John Eales motor, sold at Race Retro the month before for £57,380/$80,250, having previously been privately advertised for £69k ($96k). This car was not as cosmetically sharp as our subject car.

As a 1970, that one becomes eligible for HSCC ’70s Road Sports, though it also qualifies for HRS, being the same type as “our” car.

And that spare motor that might have made up the difference or at least added back some of the missing dollars?  Well, it doesn’t have the value you might suppose — even though it’s the item that supports the catalog claim of “matching numbers.”

The car would be matching numbers if you reinstalled the spare engine, but there are several reasons why you wouldn’t.

Eales inspected the spare engine and told me it’s an early (weak) block, almost standard except for a mild cam, that Holley carb and a different set of pistons.  Eales said he’d be amazed if it made 230 bhp. That’s before a bolt got dropped into it, damaging a piston and one of the heads.  Eales estimates its value as £500–£1,000 ($700–$1,400) tops, as with the casting damage it’s not even an ideal candidate for rebuild.

A racer or concours queen

Even though the sums don’t quite add up, in light of the sale of the identical-spec blue car, we’ll have to call it correctly valued this time, and it would appear, also judging by the blue car, that knocking off some of the shine by racing it won’t hurt its value too much, so there’s an added bonus for the new owner.  Meanwhile, the old engine will make a stylish doorstop. ♦ (Introductory description courtesy of Bonhams.)

01 Jul

2018 MOGSouth Fall Meet – Augusta Georgia

The MOGSouth Fall Meet has just been confirmed by the Hosts Glenn and Dorothy Moore.  The Meet with be held in Augusta GA, the weekend of 14 – 16 September.  

The Host Hotel will be the Partridge Inn (a Curio Collection Hotel by Hilton) and looks to be superb!  You really should ‘Google’ the hotel and you will soon see why this location is so special.

All the arrangements with the hotel and for the rest of the weekend are still being worked.   Glenn and Dorothy are working the details, etc., so a specific group rate will be arranged and will be announced, as soon as it is available.

In the meantime, you will want to pencil in the dates, and we will plan on seeing you there!

28 Jun

Williamsburg VA – ‘Morgans Making Whoopee’ – Report from the Field

“Morgans Making Whoopee” was held June 22 – 24 at the Ford’s Colony Marriott Country Club in Williamsburg VA.  The beautiful club setting included pools, tennis courts, golf course, great restaurants, all within walking distance from the lodging.

15 Morgans lined the circular drive of the club house.

Country ride to the Berkeley Plantation was enjoyed by those who were able to arrive on Friday.  Dinner following the plantation was at Indian Field’s Tavern.  Food, renewing friendships and meeting new owners was great.  Driving back to the hotel was challenging due to a torrential storm.

Directions for the Rally by Bob and Missy McKenna were written in rhyme!  First you needed to decipher the rhyme to figure out what you were looking for which added to the fun while you passed Morgans coming and going as they missed the clue.     We must have guessed correctly as we were ‘given’ 3rd place even though our mileage was twice the others.

Taking a ferry ride to the Surry Seafood House was enjoyed and gave more time for ‘noggin’.

Autocross and Gymkhana were well done.   Karen, who has been driving Morgans for 50 years won the Women’s Autocross.

The Banquet Dinner at the club was most likely the best banquet meal we have ever experienced.  More laughter than business as we had 2 who couldn’t seem to ‘behave’.  Never have I laughed so hard thanks to Joe T. and Barry A. – best ‘off the cuff’ comedy we have experienced in years!

MOGSouth members were there ‘in force’ – The Buckleys, Leos, Topinkas, McKennas, and Bernaths.

Our wonderful hosts Bruce and Gail Trabb, MOGSouth members, planned a fun filled 3-day meet.

MOGSouth members were there ‘in force’ – The Buckleys, Leos, Topinkas, McKennas, and Bernaths.

Congrats to the Leo’s for their 1st place Concours win with their beautiful 4/4.

Sideline – on the way home we stopped in New Bern NC and ate at Morgan’s Tavern and Grill.  Great food!

Chuck and Karen Bernath

28 Jun

New Component Morgan Cars – Standard or Base Specifications

[Folks according to my simple mind these specifications are the base specifications for the cars being targeted for the US Market.  The dealers can better answer questions about what can be modified and what cannot.  I suspect you can add options to these base specifications as you desire.   Costs for these added options are available from the dealers and will increase the price of the cars, as previously published.  These specifications have been provided by MorganWest’s Dennis Glavis.  Thanks Dennis!!  Cheers, Mark]

To assist with your order process, please find below the standard specification of the +4 and Roadster models-

PAINT – choice from 6 solid paint colours – SPORT BLACK, SPORT BLUE, SPORT GREEN, SPORT DOVE GREY, SPORT IVORY, SPORT RED

LEATHER – choice from YARWOOD BLACK, or YARWOOD HONEY (TAN)

HOOD – BLACK PVC ‘EASY-UP / 20 SECOND’ HOOD WITH MATCHING BLACK PVC SIDESCREENS

CARPETS – BLACK

DASHBOARD – painted in body colour

SEATS – sports recliners

WHEELS

– (+4) – wires, painted grey, 6” rims, no spare wheel

– (Roadster) – alloys, painted grey, 6” rims, with spare wheel